2001 Mazda Tribute 2WD recalls and complaints

Problem: The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.

Risk: Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.

Remedy: Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.

Problem: Mazda North American Operations (Mazda) is recalling certain model year 2001-2004 Tribute vehicles manufactured May 22, 2000, through December 19, 2003, originally sold, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. These vehicles may experience excessive corrosion at the forward attachment of the lower control arm.

Risk: A separation of the lower control arm can result in a significant loss of steering control, increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will install a newly designed reinforcement cross-brace, free of charge. The recall began on May 29, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's number for this recall is 7514D.

Problem: Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.

Risk: A stuck throttle may result in very high vehicle speeds and make it difficult to stop or slow the vehicle, which could cause a crash, serious injury or death.

Remedy: Mazda will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. Remedy parts are now available. The safety recall began on September 13, 2012. Owners may contact Mazda Customer Assistance Center at 1-800-222-5500, option #6.

Problem: Mazda is recalling certain model year 2001-2002 mazda tribute vehicles manufactured from april 20, 2000, through july 19, 2002. The brake master cylinder reservoir cap can leak brake fluid. If brake fluid leaks, it could come in contact with the antilock brake system (abs) module wiring harness connector.

Risk: Corrosion may develop in the electrical connector leading melting, smoking or possible fire.

Remedy: Mazda will notify owners, and dealers will replace the vehicle's brake master cylinder reservoir cap and modify the abs electrical system, free of charge. Until the repair has been performed, vehicle owners should park their vehicles outside. The safety recall began on june 22, 2012. Owners may contact mazda at 1-800-222-5500, option 6.

Problem: On certain sport utility vehicles equipped with antilock brakes (abs), the abs module connector may have missing or dislodged wire seals. This condition could allow contamination to enter the module connector, creating a potential for an electrical short.

Risk: An electrical short might cause an abs malfunction that would illuminate the abs warning light, and in some cases, the module may overheat resulting in burning odor, smoke, and/or fire. This condition could occur either when the vehicle ignition switch is in the off position or while the vehicle is being operated.

Remedy: Dealers will inspect the wire harness connector to the abs module for missing or dislodged wire seals, and repair or replace the harness connector as appropriate. The dealer will also inspect the connector on the abs module and replace it if it is found to be corroded or damaged. The recall began on may 9, 2007. Owners may contact mazda at 1-800-222-5500.

Problem: Certain cardone master cylinders with part numbers 10-2925, 10-2987, 10-2987mza, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, and 11-3156, and with date codes lower than dca7078 sold as replacement equipment for use on the vehicles listed above. The seal on master cylinder can fail and leak brake fluid.

Risk: Loss of brake fluid can result in poor braking performance, possibly resulting in a vehicle crash.

Remedy: Cardone will notify owners and offer to repurchase any defective master cylinders. The recall began during april 2007. Owners can contact cardone at 1-800-777-4780.

Problem: Certain 2004-2005 sport utility vehicles and certain 2001-2003 sport utility vehicle having rear liftgate components serviced with 2004 equivalent components fail to comply with the requirements of federal motor vehicle safety standard no. 206, 'door locks and door retention components.' the rear liftgate latching system does not meet the inertia load requirement in one direction.

Risk: If the liftgate is left unlocked, there is the potential that it may open during a crash.

Remedy: Dealers will replace the rear liftgate latch release rod, the release rod attachment clip and the door handle return spring. The recall began on march 31, 2005. Owners should contact mazda at 1-800-222-5500.

Problem: On certain sport utility vehicles equipped with 3.0l v6 duratec engines , during deceleration, the engine can stall.

Risk: Should the engine stall, a vehicle crash could occur.

Remedy: Dealers will reprogram the power control module (pcm) with the appropriate calibration. The recall began on may 3, 2004. Owners should contact mazda at 1-800-222-5500.

Problem: On certain sport utility vehicles, a post within the safety belt buckle covers could fracture, which could affect latch function, resulting in either a "no latch" or "partial latch" condition. In the "partial latch" condition, the buckle tongue can be inserted into the buckle and appear to be engaged, but will release from the buckle without the push button being depressed when a relatively low load is applied, such as when an occupant moves slightly in the seat.

Risk: In the event of a crash, the seat occupant may not be properly restrained, increasing the risk of injury.

Remedy: Dealers will have the driver and front passenger safety belt buckle cover removed and replaced with a newly designed service buckle cover. Owner notification began february 5, 2004. Owners should contact mazda at 1-800-222-5500.

Problem: Vehicle description: sport utility vehicles. The windshield wiper linkage can disengage due to a broken ball socket.

Risk: This condition will likely result in sudden and complete loss of the windshield wiper function, or of the wiper function on the driver side only, increasing the risk of a crash.

Remedy: Dealers will inspect and, if necessary, replace the wiper module.

Problem: Vehicle description: certain sport utility vehicles fail to comply with requirements of fmvss no. 225, "child restraint anchorage systems." the owner's manuals do not indicate which seating positions are equipped with child restraint anchorages. Also, the manuals do not explain the markings in the vehicles that locate the lower anchorages.

Risk: In the event of a crash, the child seat may not be properly attached increasing the risk of injury to the child.

Remedy: Owners will be provided with revised owner manuals.

Problem: Vehicle description: sport utility vehicles. The o-ring seals in the fuel line connector at the outlet end of the fuel filter were damaged when the line was connected to the filter during vehicle assembly. In some cases, this damage could result in a fuel odor, or possibly in fuel dripping from the connection.

Risk: Fuel leakage, in the presence of an ignition source, could result in a fire.

Remedy: Dealers will inspect and, if necessary, replace the fuel line.

Problem: Vehicle description: some 4x2 sport utility vehicles not equipped with an antilock braking system may have inadvertently been built with 4x4 rear hubs instead of 4x2 hubs. If the incorrect hubs are installed on a 4x2 vehicle, the rear wheels can loosen, or in some cases, separate from the vehicle.

Risk: This condition could cause loss of control of the vehicle, increasing the risk of a crash.

Remedy: Dealers will inspect the rear hubs and, if necessary, replace them.

Problem: Vehicle description: sport utility vehicles equipped with speed control. The speed control cable can have a cracked or missing speed control cable servo cap locating tab. The locating tab could enter the servo clutch cavity and interfere with the speed control servo clutch. Also, water could enter those units that contain a cracked or missing servo cap locating tab, eventually causing corrosion that could interfere with the function of the speed control.

Risk: If either of these conditions occurs and the speed control is used, the speed control could prevent the throttle from returning to idle, resulting in a stuck throttle. A stuck throttle could result in a crash.

Remedy: Dealers will inspect the speed control cables. Vehicles with speed control cables from cavities 3 and 4 will have the cable the speed control servo replaced.

Problem: Vehicle description: sport utility vehicles. These vehicles may have a mis-assembled or incorrectly manufactured nut that attaches the steering wheel assembly to the steering column. The nut could be upside down in the steering wheel assembly, which could overstress the steering column shaft when the nut is tightened. In addition, some of the nuts may have been cracked during manufacture resulting in the nut fracturing when it is tightened during vehicle assembly.

Risk: Either of these conditions can lead to the steering wheel becoming loose or separating from the steering column, resulting in loss of steering control.

Remedy: Dealers will inspect and replace the steering wheel retention armature and, if necessary, the steering column to correct this condition.